Customer Testimonials

With Wisconsin Oven's products, the initial run-up to operating temperature takes 14 minutes and total baking time is reduced by one to three hoursper batch. We used to complete one or two batches each day and now we complete four to six batches each day. We have gained 75% - 80% in time and will see a Return-on-Investment in less than nine months.

Dan Strobach

Read the full case study on Northwire here.

Hi David

We have had two Wisconsin Oven ovens (500° maximum temperature) running 4 days a week (sometimes on Fridays too), 9 to 10 hours a day. One oven is 10 Ft long and the other is 20 ft long.

We have had to replace one fuse and one light bulb. I have replaced the bearings and belts as a preventive maintenance measure.

Our ovens have never failed to start up and run the duration of the work day. We do powder coating and Mil spec painting, so fast cure and fast recovery is a must. Both ovens recover to set temp in less than 10 minutes after we close the doors (they are mainly ran 380 F to 420 F). We ordered double insulation for fast recovery and we are not disappointed in the speed and very low gas bills. I could not be more pleased.

I have had many ovens for not only Paint, Powder and Teflon and I can say in my 35 years of production, I have not had a finer set of ovens. If we ever expand to more ovens our only choice will be Wisconsin Oven Corporation.

Last word, the sales and service people of Wisconsin are very quick to respond to my questions about service and are very concise and clear. Again, I could not be more pleased with Wisconsin Oven in that area.

Thank you,

Drexel Ferguson

Men,

I just wanted to let you know what an exceptional young man you have in Corey. It was an absolute pleasureworking with him. He not only got the job done, but it was the way in which he did it that made him stand out. Not only was he here early every day, never took a lunch or a break the entire time he was here, but he also worked late every night, not wanting to go home until he felt the results were good, and we could test during the night. He stayed until 10:30 one night making one last adjustment he felt would do the job (It did!).

When working with our third party calibrator, this is what he had to say about him: "You know, most people work for the paycheck nowadays, and not for the company, their always thinking about themselves. This man works for the company. Everything is for Wisconsin, not him. All praise goes to his company and coworkers, not him. You just don't see this very often in this day and age" (He's 71).

He must have apologized 5 times for sending the ovens out wired incorrectly, and the other issues. Said that was very rare, and now his job was to make it right, and make me happy with Wisconsin (again Wisconsin, not him). Stated that: "If Wisconsin is doing well, he will do well. So it's important for the company to have a good name, and happy customers. Knows he has to do his part, so everyone is successful."

If we all had more workers like Corey (and I believe Wisconsin has quite a few), we would all be in a better place. Great job to whomever is responsible for growing him (although I suspect he couldn't be any other way. A rare find indeed…worthy, but humble at the same time).

You could not of sent a better man to represent Wisconsin!

Sincerely,

Ed Daigle
Manufacturing Engineer

Hi Doug,

The oven has arrived in one piece and that's good, even better we've positioned, wired, plumbed and gave her a test spin this afternoon and all looks good.

All of us here think this an awesome piece of equipment and extremely well built, we'll perform the TUS later next week. Please pass a job well done to everyone involved with the project as I think it's great!

Thanks,

Shaun Fitzgerald

Manufacturing Supervisor

Hi Doug and Elwyn,

Here's a picture of our Wisconsin Oven fully commissioned and in location. We operate the oven under AMS-2750 and maintain a ± 5° F at 1,000°. Since we commissioned the oven back in September we've had no failures or issues of any kind, it does exactly as promised all day, every day. This oven is the backbone of our Heat Treat department and something we, as an Aerospace company, depend on. For the money spent I would challenge anyone to find a better buy for the quality of product received, but more importantly the technical knowledge of Wisconsin Oven has been a home run for us. Kelowna Flightcraft is proud to own a piece of equipment of this caliber and proud to show it off.

You may use anything I have written in this or previous emails and you can use me as a reference. If I had had to change anything about this entire experience, it would be nothing as it went that good and it is that good! Thanks Guys!

Shaun Fitzgerald

Manufacturing Supervisor

To Wisconsin Oven,

Our Company had been using “Brand X” Ovens since 1967. The first two units served us well for over 20 years but, each time we would buy a new or replacement Oven we would have issues with performance and / or build quality.

In 2009, when it came time to replace our largest Oven, we knew that we needed to look for a new supplier. Due to the quality of design and the Sales Reps knowledge of what he was selling, it became apparent early in the quoting process that Wisconsin Oven was the one to go with.

When we purchased the first Wisconsin Oven it was a substantial purchase for us, not only cost wise, but size, as it was the largest (5 foot cube) that we use for our process.

The Oven had to meet stringent AMS 2750D Requirements and our own scrutiny, which is almost as tough. The Oven passed with flying colors right out of the box.

We were thoroughly impressed with all aspects of the purchase of this piece of equipment. Everyone involved was very professional, knowledgeable, helpful and efficient in making it happen. I really appreciate the fact that there were no surprises. Price, lead time and shipping were as stated, in fact we liked this Oven so much we purchased another in 2011 and are equally happy with it.

I know we made a good choice when I heard “I wish they were all like this” from the company we use to do Calibration and Temperature Uniformity Surveys. I would certainly recommend Wisconsin Oven and its sales and support staff to anyone.

Don Leonard

Hi Tom,

We are very happy with all your ovens, as well as your organization. The communication and attention to detail your company provides is second to none. Working with Linda on the five ovens we have purchased has certainly made the process easy for me.

Thanks,

Donna